Not a spy movie but a family of homebrew ham transmitters. The
6L6 is a beam power pentode vacuum tube introduced by RCA in 1936 that kind of caught on -- and caught on big: they're still making them. You'll find them in guitar amplifiers and some esoteric hi-fi amps, too (though purists there are now into triodes and are keeping the WeCo 300B in production for the rest of us).
Hams quickly latched onto the new tube -- it was relatively inexpensive for the power level -- and even though it was marketed as an audio amplifier, the lost no time in seeing if the 6L6 was happy with RF.
It was. Eventually, even RCA had to admit it and someone in the transmitting tube managed to sneak the 807 into production -- essentially, a souped-up, RF-ready 6L6.* But the cheaper receiving tube had won a place in the amateur pantheon and went on the become the heart of thousands of little transmitter designs. (There were plenty of
807 ham rigs built, too).
Fred Sutter's "QSL" series of transmitters -- so named because the little rigs had a footprint no larger than a 4" x 5" postcard (hams exchange
QSL cards to confirm two-way contact: talk to enough people, far enough away, and you can get a fancy award!) -- were justly famous; mine is safely (I hope) stashed away Somewhere Around here. Frank Jones (of
Radio magazine ham handbook fame) offered his own versions (
schematic and a nice example at this link) and I have built a couple of those:

The first one is a sort-of breadboard: the DC and heater wiring is all underneath. The empty socket at the left is for the frequency-determining crystal, the first variable condenser is plate tank tuning and the second one is output loading. But its a 1930s design, with relatively low-C (50 pF) and the output circuit is not a pi-network: the "loading" condenser is fed from a center-tap on the tank coil. This means harmonics do get out; at my former location, the first time I fired it up on 80 meters, the ham down the alley was knocking on my hamshack window in minutes, having copied my callsign via his TV receiver. (It did okay on 40 meters). This little rig worked all over the continental U.S. The frames of both tuning condensers are "hot" with plate voltage, by the way, but stubby insulating couplings and nice big knobs reduce the odds of getting bit. (Key jack, lower left, is in the cathode-ground circuit -- touch the cathode side when the key is open and you'll get a nasty tingle).
Another 6L6 rig, I built in a candy tin. Shown here sitting atop my RME-45 receiver to show how small it is (and to show off the receiver; I was copying W1AW and trying to keep up with some QRS guys earlier tonight, with a 6' hank of wire for an antenna since there was a storm outside: RME built
good receivers).

There should be a coil plugged in the socket at the right -- my box of transmitting coils is also Around Here Somewhere. This one does have a newer-type pi-net output, though a little more C on the output side wouldn't hurt. The crystal socket is out of sight behind the tube.

And here's the mysterious inner workings -- a couple of RF chokes (plus the tinned-busbar VHF choke just left of center -- the breadboard rig has one, too), a voltage divider for the screen, grid resistor, feedback condenser, cathode resistor and a whole lot of bypass condensers. The BNC connector was for a VFO but I never wired it up. there are a couple of little braces soldered in place, too -- the sheet metal candy tins are made of isn't as sturdy as a real chassis. Oh, don't be fooled by the meter scale (0 to 5
Amps); that's one of a batch of meters surplussed from a 1950s RCA commercial transmitter, all 1 Ma/1 V/1kOhm. Very easy to shunt for the range desired, in this case 0-100 mA).
___________________________
*All-glass, with a low-loss base; 6L6s were made in both metal and glass-envelope variants. Much later, the 807 begat the TV receiver sweep tube 6BG6, little more than an 807 with an octal base. The 6L6 was scaled down (6V6), scaled up (6550) and made in industrial versions, too.